Starting on new ESP32 mini

bedroom_tkm1.yaml

@@ -0,0 +1,111 @@
+esphome:
+  name: bedroom_tkm1
+  platform: ESP32
+  board: esp-wrover-kit
+  on_boot:
+    priority: 900
+    then:
+      - lambda: |-
+          id(wake_up_reason) = log(esp_sleep_get_ext1_wakeup_status())/log(2);
+
+wifi:
+  ssid: "Meneely"
+  password: "punxsutawney1"
+
+  # Enable fallback hotspot (captive portal) in case wifi connection fails
+  # ap:
+  #   ssid: "BigBlue1 Fallback Hotspot"
+  #   password: "QNWj7LmaNoD6"
+  manual_ip:
+    # Set this to the IP of the ESP
+    static_ip: 192.168.87.36
+    # Set this to the IP address of the router. Often ends with .1
+    gateway: 192.168.86.1
+    # The subnet of the network. 255.255.255.0 works for most home networks.
+    subnet: 255.255.254.0
+  fast_connect: True
+
+# captive_portal:
+
+# Enable logging
+logger:
+    level: INFO
+
+# Enable Home Assistant API
+api:
+
+ota:
+
+mqtt:
+  broker: 192.168.86.99
+  discovery: True
+  username: ha
+  password: lorrie
+  keepalive: 2s
+  birth_message:
+          topic: bedroom_tkm1/status
+          payload: coming_online_birth
+  will_message:
+          topic: bedroom_tkm1/status
+          payload: going_offline_will
+  on_message:
+    topic: bedroom_tkm1/ota_mode
+    payload: 'ON'
+    then:
+      - deep_sleep.prevent: deep_sleep_1
+
+deep_sleep:
+        run_duration: 20s
+        sleep_duration: 1min #24h
+        esp32_ext1_wakeup: 
+                pins: #[12] #, 14, 27]
+                  - GPIO12
+                  - GPIO14
+                  - GPIO27
+                mode: ANY_HIGH
+        id: deep_sleep_1
+
+globals:
+        - id: wake_up_reason
+          type: int
+          restore_value: no
+          initial_value: '0'
+
+sensor:
+  - platform: template
+    name: "Remote Control Wake Reason"
+    accuracy_decimals: 0
+    lambda: |-
+            return id(wake_up_reason);
+    on_value:
+      then:
+        - if:
+            condition:
+              lambda: 'return id(wake_up_reason) == 12;'
+            then:
+              - logger.log: "12, Green wire touched"
+            else:
+              - logger.log: "Non-green wire touched"
+
+binary_sensor:
+  - platform: gpio
+    pin: 
+        number: GPIO12
+        mode: INPUT_PULLUP
+    filters:
+      - delayed_on: 10ms ### <---- debounce time, was 100ms
+      # - delayed_off: 10s ### <---- delay to capture state change on wake up         
+    name: "TKM Test 12 (Green)"
+    id: tkm_test_12
+  - platform: gpio
+    pin: 
+        number: GPIO14
+        mode: INPUT_PULLUP
+    name: "TKM Test 14 (Yellow)"
+    id: tkm_test_14
+  - platform: gpio
+    pin: 
+        number: GPIO27
+        mode: INPUT_PULLUP
+    name: "TKM Test 27 (Orange)"
+    id: tkm_test27